Our life teaches us the truth of being human and doing things. Some people often make a fuss about things and are not calm. However, some people can often overcome their fears, calm down and find solutions to difficulties. We need to calm down when the diesel straw gas generator set fails in the process of using the diesel straw gas generator set. Find out the cause of the unit failure and eliminate the failure. There is no need to make a fuss. You can also solve the small fault of the straw gas generator set.

1、節溫器損壞

1. Thermostat damaged

秸稈氣發電機組如果出現水溫如過高的現象，一般是由于節溫器失效的緣故，致使冷卻液大循環流速減慢，需要購買新的節溫器進行替換。

If the water temperature of the straw gas generator set is too high, it is generally due to the failure of the thermostat, which slows down the large circulation flow rate of the coolant, and you need to purchase a new thermostat to replace it.

2、風扇皮帶開裂的解決方

2. Solution to Fan Belt Cracking

秸稈氣發電機組的電扇皮帶損壞，應立即停機進行替換。假如當下沒有條件更行替換，能夠?qū)⒃娚绕У臄嗫趦深^鉆兩個小孔，再用粗金屬絲把斷皮帶銜接進來做應急運用。需求留意的是，鉆孔和斷面間應保存恰當?shù)拈g隔，防止將孔拉裂，金屬絲的接頭應留在皮帶的外側，皮帶不要調的過緊。假如電扇皮帶損壞較嚴峻無法銜接，能夠把繩子或布帶、牛皮帶用鐵絲扎緊，編制成一根暫時運用的皮帶。格外要留意長短和粗細應與原皮帶持平，繩頭應當夾在中心綁好。

If the fan belt of the straw gas generator unit is damaged, it should be stopped immediately for replacement. If there is no condition for further replacement, two small holes can be drilled at both ends of the fracture of the original fan belt, and then thick metal wire can be used to connect the broken belt for emergency use. It should be noted that proper spacing should be kept between the drilling hole and the section to prevent the hole from being pulled apart. The joint of the metal wire should be left at the outside of the belt, and the belt should not be adjusted too tightly. If the fan belt is severely damaged and cannot be connected, the rope, cloth belt and leather belt can be fastened with iron wire to form a belt for temporary use. Special attention shall be paid to the length and thickness of the belt, which shall be equal to the original belt, and the rope head shall be clamped in the center and tied.

3、散熱器水管漏水

3. Radiator water pipe leaks

秸稈氣發電機組的使用過程中，散熱器水管內部的水溫過高，外部的溫度過低?；蚴且驗榻斩挌饨斩挌獍l(fā)電機組組的震蕩，很容易造成水箱的水管漏水的現象。秸稈氣秸稈氣發電機組組的水箱漏水可以把散煙絲放入水箱內，利用水循環的壓力，來使煙絲堵塞在散熱管的漏水處以便暫時運用。假如水箱散熱管漏水狀況較嚴峻，能夠把漏水處剪斷，再把棉花團涂上番筧者在被剪斷的散熱管處，再用鉗子把被剪斷的散熱管的頭部夾扁，再卷邊壓緊即可止住漏水狀況。

During the use of the straw gas generator set, the water temperature inside the radiator pipe is too high and the external temperature is too low. Or because of the vibration of the straw gas generator set, it is easy to cause water leakage of the water tank pipe. If the water tank of the straw gas generator set leaks, the loose cut tobacco can be put into the water tank, and the pressure of water circulation can be used to block the cut tobacco at the leaking place of the radiator pipe for temporary use. If the water leakage of the radiator pipe of the water tank is serious, the water leakage can be cut off, and then the cotton ball is coated with soap at the cut radiator pipe, and then the head of the cut radiator pipe is clamped flat with pliers, and then the water leakage can be stopped by crimping and pressing.

4、水泵漏水

4. Water pump leaks

秸稈氣發電機組使用鋁水泵，有時會出現密封不嚴的現象。應當把水封平面修磨平坦，或者把水封翻轉180°再安裝運用。假如止推橡皮圈損壞、脹大變形、繃簧彈力缺乏、折斷等，都應當予以替換，并且在安裝時牢記不要將繃簧壓死。

The straw gas generator set uses aluminum water pump, sometimes the seal is not tight. The plane of the water seal shall be polished flat, or the water seal shall be turned 180 ° before installation and operation. If the thrust rubber ring is damaged, swollen or deformed, or the tension spring is short of elasticity or broken, it should be replaced, and the tension spring should not be pressed to death during installation.

以上就是為大家介紹的有關煉化尾氣發電機組的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以專業的態度,為您提供服務http://www.dgtmcnc.com

The above is a detailed introduction to the refining tail gas generator set, and I hope it will be helpful to you. If you have any questions, please contact us. We will provide you with professional services http://www.dgtmcnc.com