天然氣發電機組發電質量良好，啟動快，工作穩定，機組優點多。但是這也需要在使用的時候注意一些事項。例如機組的開機與停機事項。小編介紹天然氣發電機組組開機、停機做好，步驟要明了!、天然氣發電機組在開機前要注意燃氣管系、燃氣部件的安裝、傳感器與控制屏組合模擬檢測等事項。接下來的機組來及事項要注意:開機前，應清理機組(旋轉部件)上放置的雜物(如盤車杠、工具、螺釘?shù)?，以免開車時工件飛出去傷人。2、開機前手動盤車時，注意先斷開起動電源，以免誤觸動起動按鈕，盤車杠飛出去傷人。天然氣發電機組運行要求

　　Natural gas generator sets have good power generation quality, fast start-up, stable operation, and many advantages. But this also requires some precautions when using. For example, the start-up and shutdown of the unit. The editor introduces how to start and stop a natural gas generator set, and the steps should be clear! Before starting the natural gas generator set, attention should be paid to the installation of the gas pipeline system and gas components, as well as the combination of sensors and control screens for simulation testing. Attention should be paid to the next steps of the unit: Before starting up, any debris (such as turning bars, tools, screws, etc.) placed on the rotating parts of the unit should be cleaned to prevent workpieces from flying out and injuring people during operation. 2. When manually turning the gear before starting up, be sure to disconnect the starting power first to avoid accidentally triggering the starting button and causing the gear lever to fly out and injure people. Operating requirements for natural gas generator sets

　　1、啟動時，先踏下腳踏開關，按下啟動按鈕，將缸內燃氣排空后再開啟燃氣閥門，嚴禁先給燃氣再按啟動按鈕，啟動不成功或啟動后又熄火時，應關閉燃氣閥門，查清原因，排凈缸內混合氣體后，再按規定程序重新啟動。啟動成功后，應踢開腳踏開關。

　　1. When starting, first step on the foot switch and press the start button to exhaust the gas in the cylinder before opening the gas valve. It is strictly prohibited to supply gas first and then press the start button. If the start is unsuccessful or the engine stalls after starting, the gas valve should be closed, the cause should be investigated, and the mixed gas in the cylinder should be discharged before restarting according to the prescribed procedure. After successful startup, the foot switch should be kicked off.

　　開機時，打開門窗，開動排風裝置，直到停機。

　　When starting up, open the doors and windows, activate the exhaust system until the machine stops.

　　3、操作者在機房內操作時，應戴安全帽或頭盔，機器運轉過程中不能直接面對防爆門，應避開飛輪等高速旋轉件，不能觸摸排氣管等高溫件

　　3. When operating in the computer room, operators should wear safety helmets or helmets. During machine operation, they should not face the explosion-proof door directly, avoid high-speed rotating parts such as flywheels, and should not touch high-temperature parts such as exhaust pipes

　　4、運行中，若發現燃氣有泄漏情況，操作人員應卸掉負荷并停機檢查。

　　4. During operation, if gas leakage is found, the operator should unload the load and stop the machine for inspection.

　　5、機組運行時，注意燃氣發動機防爆安全門，一旦爆破(其聲音較大)應關閉氣源，換防爆膠皮后方可重新啟動。

　　5. When the unit is running, pay attention to the explosion-proof safety door of the gas engine. Once it bursts (with loud noise), the gas source should be turned off and the explosion-proof rubber should be replaced before restarting.

　　天然氣發電機組停機應采取的措施

　　Measures to be taken for shutdown of natural gas generator units

　　1、正常停機時，應先使機組在總速運轉至水溫、油溫降到60℃以下后再切斷氣源停機

　　1. When shutting down normally, the unit should be operated at full speed until the water temperature and oil temperature drop below 60 ℃ before cutting off the gas source and shutting down

　　2、緊急停機后，應“盤車、泵油”至水溫、油溫降到60℃以下后再切斷氣源停機。

　　2. After emergency shutdown, the engine should be turned and the oil should be pumped until the water temperature drops below 60 ℃ before cutting off the gas source and shutting down.

　　3、停機后，應將“電磁閥電源”開關置于“關(OFF)”位置，并關閉燃氣總閥門。

　　3. After shutdown, the "solenoid valve power" switch should be placed in the "OFF" position and the gas main valve should be closed.

　　本文由  天然氣發電機組    友情奉獻.更多有關的知識請點擊  http://www.dgtmcnc.com/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a natural gas generator set For more related knowledge, please click http://www.dgtmcnc.com/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.